Effects of Shot Peening Cyclic Load on Fatigue Crack Propagation Life of 2024T351 Aluminum Alloy

المؤلفون

  • Fareg S Ali Department of Mechanical Engineering, College of Technical and Sciences Bani Walid , Bani Walid , Libya مؤلف
  • Abdulghadar A. M Awheda Department of Mechanical Engineering, Higher Institute of Engineering Technologies, Bani Walid, Bani Walid , Libya مؤلف
  • Abdussalam A Ahmed Department of Mechanical Engineering, Faculty of Engineering, Bani Waleed University, , Bani Walid , Libya مؤلف

DOI:

https://doi.org/10.58916/jhas.v9i5.561

الكلمات المفتاحية:

Shot peen، Cyclic load، Fatigue life، intensity، Residual stress

الملخص

Surface treatments like shot peening are frequently employed to bolster the fatigue resistance of components. This study entails simulation and experimental investigations conducted on 2024-T351 aluminum alloy specimens subjected to three distinct shot peening treatments. The experiments involved subjecting specimens to varying intensities shot peening categorized as 4-6A, 6-8A, and 8-10A, followed by cyclic loading tests. Two different stress levels, 170MPa and 280MPa, were applied during cyclic tests for varying cycle counts ranging from 1 to 10,000 cycles. The enhanced fatigue life of peened specimens exhibited a notable increase of 28%, contingent upon the shot peening parameters. Specifically, employing higher shot peening parameters such as material of shot peen, peening velocity, and size led to greater layer of residual stresses, thereby improving fatigue life. These beneficial effects serve to impede crack initiation and propagation on component surfaces, consequently retarding crack propagation rates. Fatigue life estimation for the 2024-T351 aluminum alloy can be derived from the S-N curve based on the maximum stress experienced by the specimen. Notably, simulation results closely aligned with experimental findings.

التنزيلات

تنزيل البيانات ليس متاحًا بعد.

السيرة الشخصية للمؤلف

  • Fareg S Ali، Department of Mechanical Engineering, College of Technical and Sciences Bani Walid , Bani Walid , Libya

     

    البيانات الشخصية

    الاسم: فرج سعيد مفتاح علي                             تاريخ الميلاد:   5-7-1977

     

    Name: Fareg Saeid Moftah ALI

    الجنسية:    ليبي                                          الحالة الاجتماعية:   متزوج

    العنوان: ليبيا- بني وليد

    faragpodina@yahoo.comرقم الهاتف:     00218913737196                البريد الالكتروني:                                   

     

    الموهلات العلمية

    1-الموهل العلمي الاول:

    اسم الجامعة                المعهد العالي للمهن الهندسية طرابلس

    التخصص العام            هندسة ميكانيكة

    التخصص الدقيق          هندسة انتاج

    المعدل                     جيد جدا  بنسبة 83.23 %

    سنة التخرج               1999-2000

     

    2-الموهل العلمي الثاني (الماجستير)

     University Technology Malaysia (UTM) اسم الجامعة                جامعة التكنولوجيا الماليزية      

    التخصص العام            هندسة ميكانيكة

    التخصص الدقيق          هندسةا التصنيع المتقدم

    المعدل                      3.14          

    سنة التخرج                2008

     

    3- الموهل الثالث (الدكتوراه)

                                       University Tenaga National (UNITEN) اسم  الجامعة            جامعة الطاقة الماليزية       

    التخصص              هندسة ميكانيكة

    سنة التخرج            2017 - 2018              

     

     اللغة العربية (اللغة الام) – اللغة الانجليزية – اللغة الملاوية.- اللغات4

    5- الخبرات

    1- رئيس قطاع  التخطيط ببلدية سرت (اللجنة الشعبية للتخطيط) من عام 2001 الى عام 2005

    2- متعاون بكلية الهندسة جامعة بني وليد 2008- 2012

    3- متعاون بالمعهد العالي للالات التقيلة بني وليد 2009 - 2012

    4- متعاون بكلية العلوم قسم الفيزياء جامعة غريان 2009 - 20012

    5-استاد قار بالمعهد العالي للمهن الشاملة بني وليد من 2008 - 2013

    6- قار بكلية العلوم التقنية بني وليد من 2018 - 2022

    المنشورات العلمية

    1- نشر ورقة بحثية بعنوان

    A Review: Experimental and finite element modeling of residual stress relaxation under cyclic load of aluminium alloys, Journal of Scientific Research and Development, 11-12 March 2016.

    2- نشر ورقة بحثية بعنوان:

    Experimental and numerical investigation of surface residual stress relaxation of A2024-T351 aluminium alloy, International Journal of Pure and Applied Mathematics. March 30, 2018.                                        

    3- نشرورقة بحثية بعنوان

    Relationship between Compressive Residual Stress Relaxation and Microhardness Reduction after Cyclic Loads on Shot peened ASTM A516 Grade 70 Steel, Key Engineering Materials, 2018.

    4- نشر ورقة بحثية بعنوان:

    Experimental and finite element modeling of residual stress relaxation under cyclic load of aluminium alloys: Review, International Journal of Pure and Applied Mathematics, March 30, 2018.

    5- نشر ورقة بحثية بعنوان:

    Improvement of mechanical properties and fatigue life by shot peening process on ASTM A516 Grade 70 steel, Malaysian Journal of Fundamental and Applied Sciences (2018).

    6- نشر ورقة بحثية بعنوان:

    Experimental and finite element of residual stress relaxation in 2024T351 aluminium alloys duo to cyclic loading at room temperatures: A Review, 4th NatGrad Conference April 26-27, 2017 UNITEN, Malaysia.

    7- نشر ورقة بحثية بعنوان:

     Evaluation Residual Stress Relaxation Induced by Shot Peening Parameters and its Effect on Fatigue of 2024-T351 Aluminum Alloy, test engineering and management, November-December 2019

    8- نشر ورقة بحثية بعنوان:

    Early Fault Detection in Bearing with Fault Seeded on Outer Raceway at Three Different Position: Orthogonal, Centered and Opposite, International Journal of Recent Technology and Engineering (IJRTE), November 2019.

    9- نشر ورقة بحثية بعنوان:

    4D Printing in Healthcare: Technology Evaluation, Applications, and Market Size Forecasting, African Journal of Advanced Pure and Applied Sciences (AJAPAS) January 2022.

    10- نشر ورقة بحثية بعنوان:

    Analysis of Residual stresses induced by mechanical shot peening processes using the X-ray diffraction technique and finite element method of 2024-T351 Aluminum Alloy,  Albahit journal of applied sciences, 2022.

المراجع

Li, H. X., Bai, Q. L., Li, Y., Du, Q., Katgerman, L., Zhang, J. S., & Zhuang, L. Z. (2017). Mechanical properties and cold cracking evaluations of four 7××× series aluminum alloys using a newly developed index. Materials Science and Engineering: A, 698, 230-237.

Pongen, R., Birru, A. K., & Parthiban, P. (2019). Study of microstructure and mechanical properties of A713 aluminium alloy having an addition of grain refiners Al-3.5 Ti-1.5 C and Al-3Cobalt. Results in Physics, 13, 102-105.

Zhou, P., Song, Y., Hua, L., Lu, J., Zhang, J., & Wang, F. (2019). Mechanical behavior and deformation mechanism of 7075 aluminum alloy under solution induced dynamic strain aging. Materials Science and Engineering: A, 759, 498-505.

Chen, S. Y., Chen, K. H., Dong, P. X., Ye, S. P., & Huang, L. P. (2014). Effect of heat treatment on stress corrosion cracking, fracture toughness and strength of 7085 aluminum alloy. Transactions of Nonferrous Metals Society of China, 24(7), 2320-2325.

Chausov, M., Zasimchuk, E., Maruschak, P., Khyzhun, O., Pylypenko, A., Prentkovskis, O., & Brezinová, J. (2021). Influence of impact-oscillatory loading on fatigue life of aluminium alloy 2024-T351. Iranian Journal of Science and Technology, Transactions of Mechanical Engineering, 1-10.

Han, N., Zhang, X., Liu, S., Ke, B., & Xin, X. (2011). Effects of pre-stretching and ageing on the strength and fracture toughness of aluminum alloy 7050. Materials Science and Engineering 528(10-11), 3714-3721.

G. da Silva Savonov, M.G.G. Camarinha, L.O. Rocha, M.J.R. Barboza, G.V. Martins, D.A.P. Reis, (2023). Study of the influence of the RRA thermal treatment and plasma nitriding on corrosion behavior of 7075-T6 aluminum alloy, Surf. Coating. Technol. 374 736-744.

Ye, Z., Liu, D., Zhang, X., Wu, Z., & Long, F. (2019). Influence of combined shot peening and PEO treatment on corrosion fatigue behavior of 7A85 aluminum alloy. Applied Surface Science, 486, 72-79.

Azarniya, A., Taheri, A. K., & Taheri, K. K. (2019). Recent advances in ageing of 7xxx series aluminum alloys: A physical metallurgy perspective. Journal of Alloys and Compounds, 781, 945-983.

Chobaut, N., Carron, D., Arsène, S., Schloth, P., & Drezet, J. M. (2015). Quench induced residual stress prediction in heat treatable 7xxx aluminium alloy thick plates using Gleeble interrupted quench tests. Journal of Materials Processing Technology, 222, 373-380.

Ma, J., Wen, J., Li, Q., & Zhang, Q. (2013). Electrochemical polarization and corrosion behavior of Al–Zn–In based alloy in acidity and alkalinity solutions. International Journal of Hydrogen Energy, 38(34), 14896-14902.

Ma, J., Qin, C., Li, Y., Ren, F., Liu, Y., & Wang, G. (2019). Properties of reduced graphene oxide for Mg-air battery. Journal of Power Sources, 430, 244-251.

Davis, J. R. (1993). Aluminum and aluminum alloys. ASM international.

Mattson, R. L., & Coleman Jr, W. S. (1954). Effect of shot-peening variables and residual stresses on the fatigue life of leaf-spring specimens. SAE Transactions, 546-556.

Zaroog, O.S., A. Ali, B. Sahari and R. Zahari (2009), Relaxation of compressive residual stress. Part 1: Relaxation of stage I. Journal of Scientific & Industrial Research,. 68(12): p. 1035-1037.

Torres, M. A. S., & Voorwald, H. J. C. (2002). An evaluation of shot peening, residual stress and stress relaxation on the fatigue life of AISI 4340 steel. International Journal of Fatigue, 24(8), 877-886.

Story, J., G. Jarvis, H. Zonker and S. Murtha, (1993). Issues and trends in automotive aluminum sheet forming, SAE Technical Paper.

Yuan, T., Dou, M., Liu, L., Li, L., Sun, S., & Hu, C. (2023). Improving high temperature fretting fatigue performance of nickel-based single crystal superalloy by shot peening. International Journal of Fatigue, 171, 107-563.

Meng, X., Leng, X., Shan, C., Zhou, L., Zhou, J., Huang, S., & Lu, J. (2023). Vibration fatigue performance improvement in 2024-T351 aluminum alloy by ultrasonic-assisted laser shock peening. International Journal of Fatigue, 168, 107-471.

Hu, Y., Cheng, H., Yu, J., & Yao, Z. (2020). An experimental study on crack closure induced by laser peening in pre-cracked aluminum alloy 2024-T351 and fatigue life extension. International Journal of Fatigue, 130, 105232.

Zhang, M., Li, J., Song, H., & Zhang, S. (2024). Comparative study on the fatigue properties and dislocation evolution of three kinds of aluminum alloys. International Journal of Fatigue, 178, 108001.

Qin, Z., Li, B., Zhang, H., Wilfried, T. Y. A., Gao, T., & Xue, H. (2022). Effects of shot peening with different coverage on surface integrity and fatigue crack growth properties of 7B50-T7751 aluminum alloy. Engineering Failure Analysis, 133, 106010.

Kuyucak, S., & Sahoo, M. (1996). A review of the machinability of copper-base alloys. Canadian Metallurgical Quarterly, 35(1), 1-15.

ASTM, E. (2007). Standard practice for conducting force controlled constant amplitude axial fatigue tests of metallic materials. West Conshohocken

التنزيلات

منشور

2024-12-06

إصدار

القسم

Article

كيفية الاقتباس

Fareg S Ali, Abdulghadar A. M Awheda, & Abdussalam A Ahmed. (2024). Effects of Shot Peening Cyclic Load on Fatigue Crack Propagation Life of 2024T351 Aluminum Alloy. مجلة جامعة بني وليد للعلوم الإنسانية والتطبيقية, 9(5), 324-332. https://doi.org/10.58916/jhas.v9i5.561

الأعمال الأكثر قراءة لنفس المؤلف/المؤلفين

<< < 10 11 12 13 14 15 16 17 18 19 > >> 

المؤلفات المشابهة

1-10 من 26

يمكنك أيضاً إبدأ بحثاً متقدماً عن المشابهات لهذا المؤلَّف.